[ROVERNET - UK] P6B - Removing rear brakes

[Brooks]

I have done it as well at least four times...there is no need of dropping 
the diff...and it's not nearly as much work. The book has it right...it just 
takes the right tools and patience.
 The ocasional cuss word may be reqired by some  :)



----- Original Message ----- 
From: "geffandjulie" <geffandjulie at comcast.net>
To: <rovernet at lyris.ccdata.com>
Sent: Saturday, March 17, 2007 3:24 PM
Subject: Re: [ROVERNET - UK] P6B - Removing rear brakes


>I have removed the rear calipers several times without dropping the 
>differential. As I remember, the tricky bits are loosening the connecting 
>hose - tho' they can be removed with the hose attached - and twisting the 
>caliper out forward. If you can bleed the rear calipers, you can remove 
>them! Also the large bolts on the hinged mounts are difficult to loosen, 
>but once out, the shafts are easily removed.
> ----- Original Message ----- 
> From: "peter Heaster" <mph_psh at yahoo.ca>
> To: <rovernet at lyris.ccdata.com>
> Sent: Tuesday, March 13, 2007 10:33 AM
> Subject: RE: [ROVERNET - UK] P6B - Removing rear brakes
>
>
>>
>> Hi Ray,
>>
>> I'm with Paul, don't mess around, drop the Diff.
>> If you want to do it right, get it out where you can
>> see it, you'll be supprised what you find.
>>
>> The hoses, the linkage,etc. and you can make sure that
>> the adjusting mechanism is all working before you put
>> it back.
>>
>> Peter Heaster
>> British Columbia
>> Canada
>>
>>> 1.  The book statement that you can get a socket on
>>> the outer nut is Bunk.
>>> 2.  I disconnect the half shafts and remove the
>>> discs.  Access is then not bad.
>>> 3.  Dropping the diff is not too hard and if you
>>> want to do any seals on the diff, do it.
>>> 4.  It is possible to get to the bleed screw on the
>>> LH caliper.  As with Everything on a P6, possible
>>> but not easy.
>>>
>>> PVS
>>>
>>> -----Original Message-----
>>> From: rovernet-bounces at lyris.ccdata.com
>>> [mailto:rovernet-bounces at lyris.ccdata.com]On Behalf
>>> Of Ray Wilkins
>>> Sent: Monday, 12 March 2007 9:43 pm
>>> To: rovernet at lyris.ccdata.com
>>> Subject: [ROVERNET - UK] P6B - Removing rear brakes
>>>
>>>
>>> Dear fellow Roverites,
>>>
>>> I know this has been raised in the past but a lot of
>>> water (not to mention
>>> oil, coolant, trans fluid, PS fluid etc etc) has
>>> flowed under the bridge
>>> since. I am going to have to remove the rear brake
>>> callipers from my P6B and
>>> would like to hear from anyone who has any tips,
>>> pearls of wisdom etc from
>>> having done it before. I do have the Repair
>>> Operation Manual and if I don't
>>> get any responses will just follow that step by
>>> step. However, I am aware
>>> that those procedures are not necessarily the best
>>> or most efficient way and
>>> so if anyone knows of better and/or easier ways, it
>>> will be you gentlemen. I
>>> am not just going to replace the pads but also the
>>> hoses as well as
>>> recondition the callipers themselves.
>>>
>>> I await, in roveranticipation,
>>>
>>> Ray Wilkins,
>>> 1976 P6B
>>> Melbourne, Australia
>>>
>>>
>>>
>>>
>>>
>>>
>>
>>
>> __________________________________________________
>> Do You Yahoo!?
>> Tired of spam?  Yahoo! Mail has the best spam protection around
>> http://mail.yahoo.com
>>
>> _______________________________________________
>> rovernet mailing list
>> rovernet at lyris.ccdata.com
>> To unsubscribe, go to this web page, look near the bottom and follow 
>> instructions:
>> http://mailman.nipltd.com/mailman/listinfo/rovernet
>> Back-up list and photos at:
>> http://autos.groups.yahoo.com/group/Rover_net/
>
>
> _______________________________________________
> rovernet mailing list
> rovernet at lyris.ccdata.com
> To unsubscribe, go to this web page, look near the bottom and follow 
> instructions:
> http://mailman.nipltd.com/mailman/listinfo/rovernet
> Back-up list and photos at:
> http://autos.groups.yahoo.com/group/Rover_net/
>
>
> -- 
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.5.446 / Virus Database: 268.18.12/724 - Release Date: 
> 16/03/2007 12:12 PM
>
>